Shoosh Engine, Don’t Cry! The APE Racing MCCT Will Soothe You!

The Dilemma

Since day one, my 2005 Suzuki GSX-R1000 has had a bothersome top end rattle, even when it had low miles. After a few years and 26,000 miles later, the rattle seemed to get worse. I checked valve clearances twice (once at 17,000 and again at 26,000) and all clearances were in spec. I knew there had to be a way to quiet the top end down, so I asked around.

Most of the mechanically inclined friends I spoke to said it’s rare for cam chain tensioners to go bad and I should just try to push the stock tensioner out a click to see if that worked. I tried this. No change. Though I respected their opinion, I was convinced there had to be a better solution.

Not too long ago, a friend brought a 2005 Suzuki GSX-R1000 engine to me to rebuild after it started knocking at a race. Two of the bottom connecting rod bearings had spun out after just six laps. I rebuilt the engine and noticed it was equipped with a manual cam chain tensioner. I had never used one before and really had no clue what the advantages were so I started doing some research.

Automatic CCT’s vs. Hydraulic CCT’s

What I found out is the automatic cam chain tensioners that come stock with a Suzuki motorcycle (for example) have a ratchet type mechanism that holds the push rod of the tensioner to the cam chain guide and maintains tension. But after continued high r.p.m. use, it is possible for this ratchet mechanism to weaken and thus dull or wear the teeth on the push rod. This can cause the tensioner to slip which creates noise or worse, inflicts damage.

On the flip side, hydraulic tensioners use oil pressure to determine how much pressure to put on the cam chain guide and cam chain. These types of tensioners actually have a tendency to put too much tension on the chain guide under high r.p.m.s or high oil pressure conditions like during start-up. This could result in premature wear of the cam chain guide and other components, per APE Racing. Additionally, if there is any foaming of the oil or the engine loses oil pressure, this can also cause the cams to go temporarily out of time and you’re back in the same boat you would be in with a faulty automatic cam chain tensioner. The

APE Racing Manual Cam Chain Tensioner

Per Ape Racing: “The easy-access socket head adjuster screw is perfect for tight spaces. The interior o-ring design ensures that repeated adjustments will not eventually flatten the o-ring against a jam nut.”

Per Ape Racing: “The easy-access socket head adjuster screw is perfect for tight spaces. The interior o-ring design ensures that repeated adjustments will not eventually flatten the o-ring against a jam nut.”

I found the APE Racing Parts website online and starting reading about the manual cam chain tensioner (or MCCT for short). The MCCT is designed for the racer who frequently adjusts or makes changes to their engine, per APE Racing. This means the MCCT will have to be adjusted every oil change, but I believe a happy, humming engine is worth it. APE Racing’s MCCT can eliminate the possibility of the tensioner being too loose or too tight as the mechanic can set the tension himself (or herself). The tension will remain the same, regardless of oil pressure or r.p.m’s. What does this mean? The possibility of engine damage goes down dramatically and the engine runs much quieter with better performance.

As APE Racing MCCT’s are CNC machined from billet alloy to exact tolerances, they fit perfectly to the gasket surface of the engine with no modifications needed. This makes for a quick install with little hassle. After reading this information on APE Racing’s website, I was convinced the MCCT was the answer I’d been looking for.

The Install

The part number of the MCCT I received was ST1000-3-PRO. I know this one works on more than just one year/model GSX-R. Click here to see what models APE Racing currently make manual cam chain tensioners for. I did appreciate, though, how they had a link to the “how-to” page right on the packaging. And I know this is going to sound really girly, but I love the color of this tensioner too!

IMG_2050

I removed the valve cover and made sure the engine was on TDC or top dead center where the cam chain is at it’s slackest point. I checked to make sure the timing marks on the crank shaft were correct and lined up. I also checked the position of the intake and exhaust cam sprockets and marked them with a paint pen (both on the chain and on the sprocket itself) in case I needed to reset time for any reason.

IMG_2058

I removed the original, stock tensioner and placed it in a baggy.

IMG_2060

It should be noted that I removed the oil feed to the tensioner body and placed it in the baggy as well. The APE Racing MCCT will not install correctly if this oil feed nozzle is not removed.

IMG_2053

I then cleaned the gasket surface at the CCT opening.

IMG_2055

I loosened the jam nut on the MCCT and pulled the tensioner push rod all the way back up against the body. It’s best to do this when on installation to prevent the cams from jumping time as it would be prematurely set too tight.

IMG_2062

I installed the gasket to the MCCT body.

IMG_2063

I installed the MCCT, tightening down the body first and torque-ing the two body bolts to about 16 ft. lbs.

IMG_2064

I screwed in the tensioner foot or push rod while turning the engine clockwise slowly until I felt resistance against the cam chain guide. I must note it was really difficult to feel where the best stopping point was, so I screwed the push rod in until it nearly stopped, then backed it out half a turn. I turned the motor clock wise at the crank shaft and checked the cam chain tension. It should have had a 1/4’’ deflection but it was extremely tight, so I loosened the tensioner another half turn, tightened the jam nut and turned the engine clock wise again. I checked the chain tension and my timing marks and everything was spot on!

IMG_2065

 

IMG_2066

Done and ready to start!

Done and ready to start!

 “APE'S Pro Series tensioner features an internal O-ring and custom-machined adjuster bolt. The bolt is broached with a 4mm hex.”

“APE’S Pro Series tensioner features an internal O-ring and custom-machined adjuster bolt. The bolt is broached with a 4mm hex.”

Conclusion

Before I put the bike back together, I also installed NGK iridium spark plugs and swapped out the coolant. On start up, it purred like a kitten. It literally sounded like a completely different bike. All the top end rattle was absent. It was so quiet! I was so impressed at how quick and efficient the install was and how much of a difference it made! I was not expecting such a drastic change. The APE Racing MCCT really is an amazing, simple solution to an annoying problem. I highly recommend it to anyone who doesn’t mind spending extra time working on their bikes.

More about APE Racing’s MCCT

The APE Racing MCCT is available with the bolts and gasket included and is available at an m.s.r.p. of $51.65 for standard model tensioners and $89.95 for pro series tensioners.

Take a look at this detailed video on how to install the APE Racing manual cam chain tensioner on a 2005 Suzuki GSX-R1000.

Advertisements

Part 3 of Project Ninja Turtle: 300R Handlebar Conversion

If you’re going to build a streetfighter, especially a Ninja streetfighter, you need to have a bad ass handlebar that instills fear into the enemy the way a policeman’s nightstick makes a purse snatcher pee his pants. You have to be able to throw your elbows up and muscle your bike into corners and slides the way a matador grabs a bull by the horns.

To do that, you need a tough handlebar that makes you forget about the wimpy, stock risers the bike came with. These risers are basically a Steve Urkel version of what a handlebar would be if it wasn’t made by Renthal. The Renthal “Street-Fighter” bar is perfect for transforming the 300R into the streetfighter who can Hoo-doo-kin! his competition to tears.

We approached Renthal with the idea of building the Ninja Turtle and of course they were on board. Who doesn’t want to see David beat Goliath? Thanks to Renthal, we were able to acquire the “Street-Fighter” handlebar so you could see first hand how we did a seemingly impossible task in a just a few hours.

The Transformation

The stock handlebar risers had to go. Riding a 300 with these is like watching a T-Rex make a bed. Just sad.

IMG_1940

We used KX250F OE handlebar clamps to fit the Renthal Street-Fighter handlebar to the Ninja 300R’s stock upper triple.

IMG_1934

First thing’s first. To remove the stock handlebars, we had to first remove the left and right hand handlebar switches, the brake lever, perch and throttle grip.

IMG_1943

IMG_1947

To keep track of the screws for the switches, we left them in the switch assemblies.

IMG_1951

Since the bar end had never been removed before, we tried to remove it using an impact, but eventually had to turn to the torch to get it off. Say bye bye bar ends!

IMG_1952

IMG_1953

We removed the clutch lever, perch and left side switch.

IMG_1957

IMG_1959

Lastly, we used compressed air to remove the left side grip.

IMG_1960

With everything removed from the risers, we were able to take them off by removing two bolts on each side.

IMG_1973

Now that the upper triple was bare, we finally had to chance to figure out how to install the Street-Fighter handlebar without weakening the triple.

IMG_1978

We decided the best way to do it would be to use the upper two holes that were already there for the risers. This way, the Street-Fighter handlebar would be centered on the upper triple and we wouldn’t have to drill any extraneous holes.

IMG_1979

Next we removed the steering stem nut and loosened the upper triple fork clamp bolts. Please note that to remove the triple, you have to turn the forks to the side to allow the ignition switch to clear the steering neck.

IMG_1980

The bummer was even though the triple was free of the forks, the ignition switch was still connected. The ignition switch connector is located underneath the gas tank, so we had to remove the tank to disconnect the switch and remove the upper triple.

IMG_1981

We used a mill to drill the holes for KX250F bottom clamps into the 300’s upper triple. Unfortunately, the mill doesn’t come with a jig for these sorts of things, so we had to make one.

IMG_1989

The bolts attached to the KX250F bottom clamps measured at .470’’, so we matched a 15/32’’ drill bit to that size for a precise fit between the clamp and upper triple.

IMG_1992

Watching the mill do its work was as entertaining as seeing a shoe hit George W. Bush in the head. We loved it.

IMG_1993

As you can see, our measuring paid off. A perfect fit!

IMG_1994

Now for the other side…

IMG_1995

With the bolt holes drilled, we de burred the edges with a de burring tool – A classic machinist’s trick for a clean finish.

IMG_1999

After we installed the clamps, we noticed the bolts were too long. In most other cases a long bolt would be considered an endowment, but in this case it was an impediment. How do we make it so we can tighten the clamps to the upper triple with the bolts that we have?

IMG_2004

Before we continued machining, we made sure that we could fit the bars to the clamps with the holes that we drilled and still clear the ignition switch.

IMG_2005

Luck is on our side. Our machinist happened to have an extra piece of stainless steel we could use to make spacers for the bottom clamp bolts. Using a lathe, we peened a hole into the steel so when we connect the drill bit, it can drill a hole to just exceed the diameter of the bottom clamp bolt.

IMG_2011

After a little sharpening, we installed the drill bit into the lathe and drilled a hole into the steel deep enough to match the length of the spacers we needed.

IMG_2017

We measured the sections of steel and cut the spacers to our desired length.

IMG_2022

IMG_2020

Once the two spacers were cut, they’d take some fine tuning to clean up the finish.

IMG_2023

Using a belt sander, we cut a notch into each spacer so they’d clear the bolt holes for the wire/cable routing brackets on the under side of the upper triple.

IMG_2024

See! Perfect fit! Now we can tighten the clamps.

IMG_2025

Before re-installing the Street-Fighter bar and upper triple to the forks, we had to install the bar to the triple off the bike and tighten the clamps to make sure they were straight.

IMG_2029

We installed the upper triple with the handlebar on the forks and had originally thought about cutting the Street-Fighter bar shorter, but after comparing the length of the stock handlebars to the Street Fighter bar, we determined that the length was the same. We needed all the room we could get to reinstall the levers, grips and switch assemblies.

IMG_2033

Next we had to drill holes in the Street-Fighter bar in order to reinstall the switch assemblies. We were able to measure the exact length and spot where the holes needed to be to reinstall the switches just as they were before.

IMG_2035

We removed the handlebar and used a center punch to punch a divot into the bar for the drill bit. If you don’t do this, it will walk around the drilling surface and do more damage than good.

IMG_2036

Using a drill press, we drilled the holes we needed into the Street-Fighter bar. We had to sharpen the bits, as the bar’s hard exterior was putting up quite the fight.

IMG_2040

With all the machining complete, we reinstalled the Street-Fighter bar and put the bike back together. It came out so awesome! The handlebar install is so clean it looks stock, with the exception of the open holes in the upper triple, but we can fix that later.

IMG_2044

Just one hiccup. We had to reroute wiring and cables to get the switches and levers to fit with the new handlebar. Unfortunately, our Ninja Turtle is an ABS unit, which presented quite an issue with the front brake hose. It was way too short. We tried to route the hose behind the triple, but with a few turns of the handlebar, the hose was already cut from being pinched against the plastics and it was also binding behind the triple. We’d play with it for the rest of the day, but it became evident this is going to take some research. Stay tuned to see how we resolve the brake issue.

IMG_2043

What’s Next for the Ninja Turtle?

Unfortunately, we are left with a few minor problems after installing the handlebar. With the brake hose from the front master cylinder to the ABS unit being too short, we’ll need to find a longer brake line that will not only work with the ABS, but be long enough to reach the master cylinder while being safely routed with no danger of binding or tearing. In short, the Ninja Turtle needs different brakes.

Also, we’re now on a mission to find a set of bar end mirrors that can be adapted to fit inside the Street-Fighter bar’s uniquely smaller interior.

A Little About the Renthal “Street-Fighter” Handlebar

se-road-1The “Street-Fighter” handlebar (part # 789-02) is a new bar by Renthal that is designed with a bend specifically designed for street bikes and equipped with a cross brace and bar pad for a dirt-bike look and feel. The handlebar has a 7/8’’ or 22mm external diameter and fits most standard clamps and controls.

The Street-Fighter handlebar has a shot peened finish in an effort to prevent breakage or failure due to fatigue. The bar is made from 7010 T6 Aluminium, a developed alloy specifically used by Renthal to manufacture handlebars. This high-impact material has the strength of Edward’s diamond skin, which was evident when trying to drill holes for the handlebars switches. The strong material of the Street-Fighter bar is as durable as it is thick to provide some serious dampening against vibration.

The bar also has other features that are beneficial to the rider. The left side of the handlebar is knurled on the grip end to better adhere the clutch-side rubber grip to the bar surface. At the center of the handlebar is a laser etched positioning grid which really helped us to position the bar where we needed once the job was done.

List of Mods So Far

Competition Werkes GP slip-on exhaust, Competition Werkes Fender eliminator kit, Renthal 7/8’’ Street-Fighter handlebar with KX250F handlebar clamps and custom machined spacers, rreen adjustable levers (from China)

Special Thank You to Sam Rothschild

196178_3089152122493_1530828056_nWe couldn’t do this installation with the tools we had in our garage, so we had to take the Ninja Turtle to “Sam’s Man Cave,” a code name for the extremely well equipped domicile of our brother-in-law, Sam Rothschild.

Sam races an H4 Honda CR-X with Southern California NASA or National Auto Sport Association at tracks like ButtonWillow and California Speedway and he turns lap times most motorcycle road racers only dream of. He is also a driving instructor for NASA Pro Racing. Sam finished 5th in points out of 18 racers for the 2013 season.

Sam is not only a driver, but he is also a very gifted machinist and fabricator. The guy even makes his own wiring harnesses for crying out loud! He also made a custom stunt cage for our 2010 Kawasaki ZX-6R. We’re very grateful to Sam for his help with all the random projects we drop in his lap. Of course, bringing a case of beer always helps to make up for the time we take him away from his race car. Thank you!

If you’d like to see Sam drive, click here.

Tattoos and Wrenches On The Move: OC Mobile Moto

5640473690_4ecc1da2331

Photo from ocmobilemoto.com

 

Mechanics that come to you! No trucks, trailers or AAA. Stay at home, keep your bike and get it fixed.

Mechanics that come to you! No trucks, trailers or AAA. Stay at home, keep your bike and get it fixed.

Stephen Rassmussen is the owner of OC Mobile Motorcycle Mechanics based in Lake Forest, CA. Stephen started his business in 2005 “after realizing customers who brought their bikes to dealerships for maintenance were stressed out.” His business is about bringing the mechanics to the customer so the work can be done at the customer’s home. No longer does a rider in Orange County who is in need of maintenance have to spend unnecessary time away from their bike. This is not only a brave business venture on Stephen’s part, as you obviously have to be very good at what you do to feel comfortable working under the speculative eye of the customer, but it’s a tenacious endeavor to work on the road in unpredictable conditions traveling to unfamiliar areas.

The fully wrapped OC Mobile Moto truck.

The fully wrapped OC Mobile Moto truck.

“Being an entrepreneur, I started this business with the customer in mind,” says Stephen. “We have all the required tools for daily jobs.” If there is a tool Stephen doesn’t have, he does the running around to make the repair happen so you don’t have to worry about it. You mean if he worked on my bike, I could just stay at home, watch him work and I don’t have to do any driving to pick up parts or tools? I’d definitely pay for that!

Not only is Stephen a mechanic, but he’s been riding since he was 13 years old. He started out on BMX and he’s been wrenching for as long as he’s been riding. “It’s a big part of my life,” he says. “It’s what I know best.”

With the enthusiasm Stephen has for two-wheeled living, it only makes sense that he’d spend 34 hours of his life on a tattoo artist’s table to have an exact replica of the 2009 Honda CRF450R engine inked into his back as an ode to his love for Honda motorcycles and wrenching. The tattoo was done by Vance Freeman of True at Heart Tattoo in Lake Forest, CA, in 2009 after the release of the new 2009 CRF450R.

Stephen's 2009 HONDA CRF450R ENGINE BACK TATTOO

The engine in the 2009 Honda CRF450R was completely redesigned from the previous year, spinning faster at 11,450 r.p.m.’s and pushing out 56.3 bhp at 8,500 r.p.m.’s and 37.5 lb./ft. of torque at 7,000 r.p.m’s. The motor has a single overhead cam with four lobes and individual rocker arms for each exhaust valve to reduce weight which contributes to higher r.p.m. capability. The redesigned engine created a lower overall center of gravity and it is now immortalized on Stephen’s body.

Stephen's moto-themed tattoo on his left arm.

Stephen’s moto-themed tattoo on his left arm.

Because Stephen’s tattoo was featured in Transworld Motocross magazine, it got Honda’s attention. “Honda gave me some recognition and I was able to purchase a CRF450R from them for $2,500.”

Stephen has already started working on another fully bionic tattoo on his right arm and you can find another moto-themed tattoo on his left arm. Stephen is a motorcyclist for life and because he’s inked his passion into his body, I’m sure we’ll see Stephen wrenching and riding motorcycles long after he has gray hair.

 

Competition Werkes Fender Eliminator Kit for the 2013 Ninja 300R

Whenever I purchase a new motorcycle, the first thing to be removed is the kite of a mud flap hanging off the rear end. It’s unsightly, ungodly and just unacceptable. My favorite thing about riding sportbikes has always been chasing tail (no pun intended) and it wouldn’t be any fun if that tail were bigger than mine, catch my drift? So naturally, that legal, DOT compliant fender has got to go. No streetfighter of mine is going to be stuck with excess plastic.

This is why we chose to install the Competition Werkes fender eliminator kit to return the tail section to the high and tight look it was meant to have before it was tainted with an awning meanwhile remaining street legal with a license plate light and turn signals. There you go California. I haven’t completely disregarded the rules. And it only took an hour to install.

Interested in getting one for yourself? They pay attention pupils because we’re about to give you a lesson in mechanic-in.

Step 1:

Make sure you have all the necessary hardware to complete the task.

The packages should contain the license plate bracket, license plate light, short stalk turn signals and all the necessary hardware to install.

The packages should contain the license plate bracket, license plate light, short stalk turn signals and all the necessary hardware to install.

Step 2:

Remove and passenger seat and flip up the tray underneath to expose the four bolts holding the mud flap assembly and three wires routed to the turn signals and license plate light. Cut these three wires with a pair of cutters and remove the bolts with a 5mm allen socket or T-handle. Pull away the stock mud flap assembly.

The bolts and wires are located just underneath this flip-up tray.

The bolts and wires are located just underneath this flip-up tray.

Cut these wires and remove bolts with a 5mm allen.

Cut these wires and remove bolts with a 5mm allen.

Here is what the 5mm allen bolts look like from the under side (just underneath the tray). They should come out fairly easily.

Here is what the 5mm allen bolts look like from the under side (just underneath the tray). They should come out fairly easily.

Step 3:

Adhere the license plate light to underside of the top of the license plate holder and route the wires up through the center of the slot.

IMG_1769

Step 4:

Take the zip tie provided in the package and loop through the center hole of the license plate holder from the back as shown.

IMG_1778

IMG_1779

Step 5:

Retrieve the two second to longest bolts from the package. I found it easier to loosely install the turn signals and turn signal brackets to the license plate holder before installing the holder to the tail section but of course, this can wait until later.

IMG_1784

IMG_1788

Step 6:

Route the wires from each turn signal through the zip tie on the back of the license plate holder and then route the wires up through the center grommet and into the tail section.

IMG_1796

IMG_1800

Step 7:

Retrieve the four longest bolts from the package along with four washers and nuts. Install license plate holder to the tail section.

I installed the bolts nuts-up (lol) in the tail and I used a 10mm T-wrench and 4mm allen to install all four nuts and bolts.

I installed the bolts nuts-up (lol) in the tail and I used a 10mm T-wrench and 4mm allen to install all four nuts and bolts.

I loved how the license plate holder had holes to slip the T-allen wrench through in order to tighten the mounting bolts. Installation would have been a pain without them. Remember! Appreciate the little things!

I loved how the license plate holder had holes to slip the T-allen wrench through in order to tighten the mounting bolts. Installation would have been a pain without them. Remember! Appreciate the little things!

Step 8:

Adjust and tighten the turn signals so they’re facing level.

IMG_1811

Step 9:

Use the splice connectors provided to connect the turn signals to the previously cut wires. Note the sleeve with the black wire and white wire is for the license plate light. It may take a few attempts to connect the turn signals correctly, however, as both wires for each side are black and it is difficult to tell which side goes to which. Don’t worry though. You can turn the key on and hit the turn signal switch to verify both sides are blinking correctly.

Tip: I used pliers to squeeze the splice connectors onto the wires due to my lack of upper body strength. Hey, work smarter not harder!

Tip: I used pliers to squeeze the splice connectors onto the wires due to my lack of upper body strength. Hey, work smarter not harder!

Step 10:

Hook up the license plate light. I had to cut the spades that were originally crimped to the wires and strip the wires to crimp new spades. I didn’t use the ones in the package because they’re a one-time, permanent-type of connector and I want to be able to unhook the running lights if I need to.

I used a set of wire crimpers to crimp on a set of automotive-style spades. You can find these at any auto parts store.

I used a set of wire crimpers to crimp on a set of automotive-style spades. You can find these at any auto parts store.

This is the end result. It takes more time, but it's worth it to have options.

This is the end result. It takes more time, but it’s worth it to have options.

Step 11:

Tuck the wires to the side so you can close the tray above them. I wrapped the wires with electrical tape and secured them to the subframe with a zip tie to clean up the install.

I wrapped the wires in electrical tape for fear that the zip tie might eventually chaff the wiring from vibrations. Call it paranoia, but better safe than sorry.

I wrapped the wires in electrical tape for fear that the zip tie might eventually chaff the wiring from vibrations. Call it paranoia, but better safe than sorry.

Step 11:

Verify operation of all lights and install the license plate with the remaining hardware from the kit.

The license plate light is pretty potent for a couple of small LED's. Kudos to Competition Werkes on the lighting.

The license plate light is pretty potent for a couple of small LED’s. Kudos to Competition Werkes on the lighting.

Stock mud flap vs. Competition Werkes fender eliminator. Yes, Comp Werkes eliminator wins!

Stock mud flap vs. Competition Werkes fender eliminator. Yes, Comp Werkes eliminator wins!

Tools I used: 4mm allen T-wrench, 10mm and 14mm ratchet wrenches, cutters, pliers, wire crimpers (one automotive, one metric-specific)

Tools I used: 4mm allen T-wrench, 10mm and 14mm ratchet wrenches, cutters, pliers, wire crimpers (one automotive, one metric-specific) and electrical tape

The Competition Werkes fender eliminator kit for the 2013-2014 Ninja 300R includes the CNC laser cut license plate holder made from 304 stainless steel as well as short stalk turn signals and an LED license light. The entire kit is feather light compared to the heavy weight mud flap the bike is equipped with at the factory. You can purchase this kit from any Competition Werkes dealer at an m.s.r.p. of $119.95.

Competition Werkes is an aftermarket motorcycle accessories and parts company that has been producing fender eliminator kits, exhausts and parts for motorcycles since 1984. To find out more about their products, click here.

Here is how the Ninja Turtle looks with the Competition Werkes exhaust and fender eliminator kit installed. Stay tuned as the transformation resumes!

Here is how the Ninja Turtle looks with the Competition Werkes exhaust and fender eliminator kit installed. Stay tuned as the transformation resumes!

Competition Werkes GP Slip-On Exhaust System for the Ninja 300R

There is nothing like the rumble of an aftermarket exhaust while decelerating into a corner. If you’re going to build a streetfighter, you need a sound to match the look; something that gives the bike a loud, in-your-face persona and  makes people stare as you ride down the street.

In 2013, Competition Werkes developed the GP shorty slip-on exhaust system for the Ninja 300 that transforms the bike’s passive thrum into a race bike’s growl. The system produces a little more bottom end grunt to gives you a snappier feel at the throttle and leaves an inevitable grin on your face.

The system is hand crafted from 304 stainless steel and has a tapered baffle for “improved performance and advanced tuning.” The canister is small and compact giving the bike a lighter, tighter feel without sacrificing styling. We installed the stainless steel GP system on our Ninja 300R Streetfighter project bike and here’s how we did it.

Step 1:

Make sure you have all the hardware and clamps needed to install the system.

The GP exhaust system comes with the muffler, high shield, 4mm allen bolt, pipe clamp and sticker.

The GP exhaust system comes with the muffler, high shield, 4mm allen bolt, pipe clamp and sticker.

Step 2:

To remove the heat shield from the stock exhaust can, remove the 5mm allen bolt and the clamp on the mid pipe with a Phillips screwdriver.

Remove the 5mm allen bolt.

Remove the 5mm allen bolt.

Loosen the bottom clamp with the Phillips screwdriver.

Loosen the bottom clamp with the Phillips screwdriver.

Step 3:

Pull the bottom clamp on the mid pipe down or toward the front of the motorcycle, then pull the heat shield toward the front of the motorcycle to remove it.

Pull the bottom hose clamp down the mid pipe, then slide the heat shield forward (toward the front of the bike) to remove it.

Pull the bottom hose clamp down the mid pipe, then slide the heat shield forward (toward the front of the bike) to remove it.

Step 4:

To remove the stock exhaust can, loosen the clamp around the muffler with a 12mm socket or T-handle.

IMG_1672

Step 5:

Remove the 14mm bolt and nut from the rear set.

IMG_1668

Step 6:

Pull the exhaust toward the rear of the motorcycle.

IMG_1680

Notice how the stock exhaust has a muffler gasket while the Werkes USA exhaust does not. This is because the Werkes USA exhaust muffler slides forward onto the midpipe until the bolt hole for the heat shield is just forward of the rear set heel guard bolts. The Werkes USA exhaust does not need an exhaust gasket!

Stock (left), Werkes USA (right)

Stock (left), Werkes USA (right)

Step 7:

Remember to slide the Werkes USA clamp onto the mid pipe before sliding on the Werkes USA canister onto the midpipe.

IMG_1715

Put a rag over the swing arm to avoid scratching or denting the Werkes USA canister while wiggling or sliding it over the mid pipe. Note: It is a tight fit, so it takes a little body English.

IMG_1728

Clean the Werkes USA exhaust thoroughly on the outside with WD-40 or comparable cleaning substance to avoid discoloring the canister after starting the motorcycle.

Step 8:

Tighten the hose clamp. Install the new stainless steel heat shield with the 4mm allen bolt provided.

IMG_1740

Final Step:

Make sure you clean the outside of the pipe with WD-40 or a comparable product before running the motorcycle to avoid discoloration.

Start and enjoy.

Tools I used: 3/8’’ ratchet with 14mm and 12mm sockets, Phillips screwdriver, 12mm T-handle, 14mm wrench 4mm/5mm T-allen wrenches

Tools I used: 3/8’’ ratchet with 14mm and 12mm sockets, Phillips screwdriver, 12mm T-handle, 14mm wrench
4mm/5mm T-allen wrenches

We put each exhaust system (both stock and the Werkes USA muffler) on the scale. The stock exhaust weighs 17.5 lbs. while the Werkes U.S.A. exhaust weighs 2.5 lbs. This is a total weight savings of 15 pounds!

We put each exhaust system (both stock and the Werkes USA muffler) on the scale. The stock exhaust weighs 17.5 lbs. while the Werkes U.S.A. exhaust weighs 2.5 lbs.
This is a total weight savings of 15 pounds!

You can purchase the GP slip-on exhaust for an m.s.r.p. of $399.95. The exhaust is also available in Carbon Fiber, Cobra Black, Cobalt Black, Tungsten, Titanium, Mag Silver, Satin Silver and Gold for $100 more, as well as Black Velvet for $50 more. The install takes roughly ten minutes and is very easy. With the Competition Werkes GP exhaust, you’ll be where on your way to a lighter, faster and better-sounding machine in no time!

Competition Werkes is an aftermarket motorcycle accessories and parts company that has been producing fender eliminator kits, exhausts and much more for motorcycles since 1984. To find out more about their products, click here.

MotoInked’s 2013 Kawasaki Ninja 300R Streetfighter Build

Say goodbye to this stock body because it's about to mutate into a bad ass fighter!

Say goodbye to this stock body because it’s about to mutate into a bad ass fighter!

Ever since the Ninja Turtles hit TV in the late 80’s, I was a kid infatuated with green things that were fun, bad ass and entertaining. Hence my affinity for Ninjas, big and small. You say Kawasaki, I say “Kawabunga!”

Michael Angelo was always my favorite turtle and it’s because of him I’ve never forgotten to appreciate the little things, no matter how underestimated they are. I say “underestimated” for a reason. You can never presume to be born with bad ass-ness, it has to be earned…or built.

This is why Michael Angelo is a muse for transforming my 2013 Kawasaki Ninja 300 into a Kawabunga streetfighter. Just like radioactive waste turned a slow, harmless turtle into a lightning quick ninja warrior, I’m going to turn my slow Ninja 300 into the envy of his bigger brothers.

I’ve scoured forums for other owners who have made the leap from clothed to naked with their 300’s but the most I’ve found that even resembled a transformation was a 250 that was smacked in the face with a 636 front end. I was disappointed to see an almost unanimous opinion across the inter webs that stripping and revamping a new 300 made about as much sense as giving a teenager a face lift. Why waste your time chopping up a new bike when you can do the same to an older, salvaged one?

You know what my answer to that one is? Because it’s already been done before! What’s the point in having a motorcycle, new or old, if you can’t make it your own, if you can’t transform it into the machine you’ve wanted since you were a kid? Why do I have to stick to the conventional, cookie-cutter showroom floor lawnmower-sounding half pint with the pretty green dress on? Why can’t I use my superpowers to turn my little ninja into the Michael Angelo I always envied as a kid? Why can’t I make my tortoise slap that silly hare on the ass? We live in America because this is the land where the naysayers can kiss my lilly white waste gate. This is the place where the haters can shout at their computer screens while I plaster my Kawa-bunga 300 turned bad ass street fighter photos all over their precious forums as shamelessly as a garage rapper peddling demos in a Wal Mart. This is my chance to turn a short woman complex into an excuse to go bigger and better than ever before.

Welcome to my adventure, ladies and gentlemen. We’re about to embark on a journey where David sends Goliath crying home to his mama. As you see it now, my little Ninja Turtle is still pretty much bone stock. He’s a ready volunteer on the surgery table and he’s ready to become a nun chuck wielding road warrior.

If you want the bully to run, you can’t stare him down from the bottom up. You have to tighten that ass and add some much needed oomph to that growl. Our first step will be to get the turtle out the gate with the pop of a new exhaust and whip that tail into shape with a Competition Werkes USA stainless steel GP slip-on exhaust and fender eliminator kit. Want to know how you turn an elephant man in a Beckham? Then get your ass back here to learn a thing or two about the installs. Stay tuned.